Updated T1 WAN Interface Card with Integrated DSU/CSU Simplifies Internet/Intranet Access by Reducing Deployment and Management Tasks.
• Fewer devices and cables to deploy and manage
• Remote and local configuration, monitoring, and troubleshooting via the Cisco IOS® Software CLI and Simple Network Management Protocol (SNMP)
• Flexibility and investment protection
• Single-vendor support
• Enhanced reliability
• Physical space savings
Figure 1. Cisco T1 DSU/CSU WAN Interface Card
FEATURES
• T1 or fractional T1 network interface
• Wet T1 support (not available on WIC-1DSU-T1)
• N x 64 kbps or N x 56 kbps nonchannelized data rates (N = 1 to 24)
• Standards-based, including ANSI T1.403 and AT&T Publication 62411
• Full management features:
–Configuration-Capability for remote configuration via Telnet from Cisco IOS CLI.
–Monitoring-Router and DSU/CSU are manageable as a single SNMP entity; extensive DSU/CSU statistics are provided by the Cisco IOS CLI.
–Troubleshooting-Extensive loopbacks (including manual button for network line loopback), bit error rate tester (BERT) test patterns, alarm counters, and performance reports, all of which are accessible from Cisco IOS CLI. LEDs for carrier detect, loopback, and alarm functions.
BENEFITS OF AN INTEGRATED, FULLY MANAGED SOLUTION
Reduced Deployment, Management Time, and Costs
• Easily configures via Cisco IOS Software initial setup, a utility that prompts a series of basic configuration questions upon router startup.
• Allows simplified remote and local configuration, management, and troubleshooting of the DSU/CSU from Cisco IOS CLI
–Using the familiar Cisco IOS CLI eliminates the need to learn or use command syntax for an external DSU/CSU
–Convenient Telnet or Secure Shell (SSH) Protocol connection to the router eliminates the need for out-of-band management of external DSUs/CSUs
–Cisco IOS CLI provides extensive DSU/CSU statistics (such as 24-hour history) and troubleshooting capability (such as DSU/CSU self test, loopbacks, DSU/CSU reset, alarm counters, and T1 statistics)
• Offers simplified SNMP management, with router and DSU/CSU managed as a single SNMP entity through CiscoWorks/CiscoView. The Cisco T1 DSU/CSU WIC SNMP agent supports the standard MIB II, Cisco integrated DSU/CSU MIB, and T1 MIB (RFC 1406). All T1 performance statistics can be monitored. The router also generates the appropriate SNMP traps in response to DSU/CSU alarms.
• An end-user-initiated manual loopback button allows users at remote sites to easily initiate a T1 network line loopback by pushing a recessed button on the WIC front panel without having to access the router via a console port or Telnet.
• Provides LEDs for carrier detect, loopback, and alarm, allowing for quick troubleshooting.
• Physical convenience-No additional space is needed because the Cisco T1 DSU/CSU WIC is inserted into the router. This integrated solution eliminates the need for a separate serial cable, reducing deployment time and cost.
• High reliability-The integrated DSU/CSU reduces the number of components in the network, leading to higher reliability. The serial cable that connects a router serial port to an external DSU/CSU is eliminated. The integrated DSU/CSU is powered from the router, eliminating the power supply for an external DSU/CSU. The Cisco 2600XM, 3600, and 3700 series are all available with redundant power systems, which cover the integrated DSU/CSU.
Flexibility and Investment Protection
Single-Vendor Support
Enhanced Reliability
Consistency with WIC-1DSU-T1
Table 1. Cisco T1 DSU/CSU WIC Features
WIC-1DSU-T1-V2 |
WIC-1DSU-T1 | |
Description |
Updated one-port T1/fractional T1 DSU/CSU WIC |
One-port T1/fractional T1 DSU/CSU WIC |
Router families supported |
1700* (1720, 1721, 1751, 1760), 2600XMs, 2691, 3631, 3725, 3745, and ICS 7750 |
1600**, 1600R2**, 1700***, 2600, 2600XM, 3600, and 3700 |
Wet T1 Capable |
Yes |
No |
Short Cable Length Command |
Yes; used to configure attenuation for short cable lengths (<660 feet) |
No |
Network Equipment Building Standards (NEBS) |
Yes: Type I/III |
No |
SPECIFICATIONS
Cisco IOS Software Release
• 12.2(15)ZL PCBU special [Cisco 1700 Series only]
• 12.2(17) Mainline
• 12.3(1) Mainline
• 12.3(1st)T
Support on IAD2430 Series
• The IAD2431-8FXS, IAD2431-16FXS, IAD2432-24FXS, IAD2431-1T1E1 are supported on the following releases:
–12.3(7)T4
–12.3(8)T6
–12.3(11)T2
• Network clock participate was added, and is available in releases:
–12.3(7)T6
–12.3(8)T6
–12.3(11)T2
Dimensions and Weight
• Width: 3.1 in. (7.9 cm)
• Height: 0.8 in. (2.1 cm)
• Depth: 4.8 in. (12.2 cm)
• Weight: 0.14 lb (62g)
Network Interface
• Transmit bit rate: 1.544 Mbps +/- 50 bps
• Receive bit rate: 1.544 Mbps +/- 100 bps
• Line code: AMI, B8ZS
• AMI ones density
–Forced/bit robbing (N X56)
–High-Level Data Link Control (HDLC) data inversion (N X64)
• Framing format: D4 (SF) and ESF
• Output level (LBO): 0, -7.5, or -15 dB
• Input level: +1 dB0 to -24 dB0
Data Interface
• Data rates
–N x 64 kbps (N = 1 through 24); nonchannelized
–N x 56 kbps (N = 1 through 24); nonchannelized
• Interface connector: RJ-45
• System timing: Network and internal
Diagnostics
• Loopbacks
–Network line loopback; user initiated
–Recessed push button for network line loopback; toggle on/off
–Network line loopback; telco initiated
–Network payload loopback
–Local date terminal equipment (DTE) loopback
–Remote line and payload loopback (codes: V.54 loop up, and loop down)
• Self-test
–Self-test activated by user
• Test patterns (BERT)
–1:2, 1:5, 1:8, 3:24, QRW, All 0s, All 1s, user-programmable 24-bit patterns
• Network (T1) alarms
–Red alarm: Loss of network signal
–Blue alarm: Loss of network frame (AIS) from network
–Yellow alarm: Receive from network
• Performance reports and error counters
–Cyclic redundancy check (CRC), bipolar violation (BPV), OOF [EXPAND?], errored seconds, burst errored seconds, severely errored seconds, Ft and Fs framing errors for SF framing, FPS [EXPAND?] framing errors for ESF framing, 24-hour history stored in 15-minute increments
• LEDs
–CD (data carrier detect)
–LP (loopback)
–AL (alarm)
Management
• Telnet/console
–Remote and local configuration, monitoring, and troubleshooting from Cisco IOS CLI
• SNMP
–Router and DSU/CSU managed by single SNMP agent; router, DSU, and CSU appear as a single network entity to user
–Standard MIB (MIB II)
–Cisco integrated DSU/CSU MIB
–RFC 1406
• SNMP traps
–Generated in response to alarms
Regulatory Compliance
• FCC Part 15 Class B
• TIA/EIA-IS-968
• Industry Canada CS-03 Part II
• JATE Digital
• CAN/CSA-C22.2 No. 60950-00
• UL 60950-2000
• IEC/EN 60950
• TS001
• AS/NZS 3260
• NEBS Type I/III
Standards
• AT&T Pub 62411
• ANSI T1.403
Environmental
• Operating temperature
–0 to 40ºC (32 to 104°F)
• Storage temperature
–-20 to 65ºC (-4 to 149°F)
• Relative humidity
–10 to 85 percent noncondensing operating; 5 to 95 percent noncondensing, nonoperating
Table 2. Ordering Information
Product Number |
Description |
WIC-1DSU-T1-V2 |
Updated one-port T1/fractional T1 DSU/CSU WIC |
댓글을 달아 주세요